| Hardware Specifications |
| Copper Ports |
LAN: 5 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port 1 to Port 5, bridge mode)
WAN: 1 10/100/1000Mbps auto MDI/MDI-X RJ45 port (Port 5, gateway mode) |
| PoE Injector Port |
4 ports with 802.3af/802.3at PoE injector function (Port 1 to Port 4) |
| USB |
1 USB Type A female for setting backup |
| Power Output |
4 PoE out 51VDC; max. 36 watts per PoE port
2 DC out 24@ 2A maximum (four-pin terminal block)
* The voltage of DC out is based on the battery. |
| Switch Architecture |
Store-and-Forward |
| Switch Fabric |
10Gbps/non-blocking |
| Switch Throughput@64 bytes |
5.95Mpps@64 bytes |
| MAC Address Table |
8K entries |
| Shared Data Buffer |
512Kbit |
| Flow Control |
IEEE 802.3x pause frame for full duplex
Back pressure for half duplex |
| Reset Button |
< 5 sec: System reboot
> 10 sec: Factory default |
| LED Indicators |
3 LEDs for System and Power:
- Green: Power
- Red: Alarm
- Green: PV System
4 LEDs for PoE Copper Ports (Port 1~Port 4):
- Green: LNK/ACT
- Amber: PoE-in-use
1 LED for 10/100/1000T Copper Port (Port 5):
- Green: LNK/ACT
3 LEDs for PoE Power Usage (W)
- Amber: 50, 100 and 120W |
| Connector |
Removable 6-pin terminal block
Pin 1/2 for PV panel; Pin 3/4 for alarm; Pin 5/6 for battery |
| Alarm |
1 digital output (DO):
Level 0: -24V~2.1V (±0.1V)
Level 1: 2.1V~24V (±0.1V)
Open collector to 24V DC, 100mA max. |
| Power Requirements |
PV in: 24~45V DC
Battery in/out: 24V DC |
| Power Consumption/ Dissipation |
5.04 watts, 17.1BTU (Standby without PoE function)
6.96 watts, 23.7 BTU (Full loading without PoE function)
135.36 watts, 461.5 BTU (Full loading with PoE function) |
| Dimensions (W x D x H) |
86.8 x 107.3 x 152 mm |
| Weight |
1251g |
| ESD Protection |
6KV DC |
| Enclosure |
IP30 aluminum case |
| Installation |
DIN-rail kit and wall-mount ear |
| Power over Ethernet |
| PoE Standard |
IEEE 802.3af/802.3at Power over Ethernet PSE |
| PoE Power Supply Type |
End-span |
| PoE Power Output |
Per port 51V DC, 275mA. Max. 15.4 watts (IEEE 802.3af)
Per port 51V DC, 535mA. Max. 36 watts (IEEE 802.3at) |
| Power Pin Assignment |
1/2 (+), 3/6 (-) |
| PoE Power Budget |
120 watts (PoE consumption + DC out and depending on power input) |
| Max. Number of Class 2 PDs |
4 |
| Max. Number of Class 3 PDs |
4 |
| Max. Number of Class 4 PDs |
4 |
| Renewable Power Input (PV IN) |
| Min. Voltage |
24V (Suggest > 30V for fully charge to battery) |
| Max. Voltage |
45V |
| Max. Current |
< 8.8A |
| Max. Power |
< 400W |
| Battery Information |
| Type |
Lithium Battery (Default)
Lead-acid Battery |
| FCV |
Lithium Battery (Default)
fixed 26.6V
Lead-acid Battery
27.2V (26.0~30.0V) |
| ACV |
Lithium Battery (Default)
fixed 28.7V
Lead-acid Battery
29.2V (28.0~32.0V) |
| LVD (Low Voltage Disconnection) |
Lithium Battery (Default)
21.3V (19.6~23.0V)
Lead-acid Battery
22.2V (21.0~23.0V) |
| LVR (Low Voltage Reconnection) |
Lithium Battery (Default)
24.0V (23.5~25.0V)
Lead-acid Battery
23.5V (23.5~27.0V) |
| Router Features |
| Internet Connection Type |
Shares data and Internet access with users, supporting the following internet accesses:
- PPPoE
- Dynamic IP
- Static IP
- PPTP
- L2TP |
| Firewall |
NAT firewall with SPI (Stateful Packet Inspection)
Built-in NAT server supporting Port Forwarding, and DMZ
Built-in firewall with IP address/MAC address/Port/ URL filtering
Supports ICMP-FLOOD, UDP-FLOOD, TCP-SYN-FLOOD filter, DoS protection |
| Routing Protocol |
Static/Dynamic (RIP1 and 2) routing |
| VPN Pass-through |
PPTP, L2TP, IPSec, IPv6 |
| LAN |
Built-in DHCP server supporting static IP address distribution
Supports UPnP, Dynamic DNS
Supports IGMP Proxy
Supports 802.1d STP (Spanning Tree)
IP/MAC-based bandwidth control |
| Management |
| Management Interface |
Setting up of system/management functions
Web firmware upgrade
SNMP trap for alarm notification of events |
| PoE Management |
Power limit by consumption and allocation
PoE admin mode
Per port power schedule
Per port power enable/disable
Power feeding priority
Current per port usage and status
Total power consumption
PD alive check
Scheduled power recycling |
| Battery Management |
Current battery usage status
Low voltage cut-off protection
Fully-charged hold time protection |
| PLANET ONVIF IP Camera Management |
Supports PLANET ONVIF IP camera discovery
A maximum of four PLANET ONVIF IP cameras can be powered by one BSP-360 switch.
Supports IP camera snapshot function in the LAN. |
| Standards Conformance |
| Regulatory Compliance |
FCC Part 15 Class A, CE |
| Standards Compliance |
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit Ethernet
IEEE 802.3x Flow Control and Back Pressure
IEEE 802.1D Spanning Tree Protocol
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
RFC 768: UDP
RFC 791: IP
RFC 2068 HTTP
RFC 1157: SNMP v1
RFC 1902: SNMP v2c
RFC 5424: Syslog |
| Environment |
| Operating |
Temperature: -10 ~ 60 degrees C
Relative Humidity: 5 ~ 95% (non-condensing) |
| Storage |
Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 95% (non-condensing) |
Site Map
Contact Us
RSS